Machine must be assembled in sure to remove them before starting the machine. Align holes in chipper base 1 with the holes in To attach handle 9 to shredder hopper 10 install four axle weldment 2 and the support leg 3.
Stop engine, wait for all parts to stop moving and 2. Remove key from key switch. Allow the engine and muffler to cool for at Check the oil level and, if needed, fill the engine crankcase least three minutes.
The following descriptions define the features and controls of your machine. Move lever to the choke position when starting. Move lever to the run position when engine is running. Refer to engine manual for further engine operating instructions. Alternate green or fresh cut material with dry 3. If the chipper engine stalls while engaging the belt, return the engagement handle back to the START material to lubricate the chipping blades for position, restart engine, SLIGHTLY increase throttle longer life and better performance.
The belt should remain engaged during the entire shutdown process. The rotor will continue to turn for some time after the Leaving the belt engaged is a vital part of proper engine has been shut off. This schedule is designed for units operating under To prevent personal injury or property damage: shut normal conditions. Wear safety glasses at all times while operating this machine. One pair of safety glasses is provided. Avoid wearing loose fitting clothing. Never operate this machine wearing clothing with drawstrings that could wrap around or get caught in the machine.
Check that all screws, nuts, bolts, and other fasteners are properly secured before starting the machine. Check all screws, nuts, bolts, and other fasteners for proper tightness to ensure everything is in proper working condition once every 10 hours of operation.
Keep all guards, deflectors, and shields in place and in good working condition. Do not transport or move machine while the machine is running. Do not allow hands, or any part of body or clothing, inside the feeding chamber, discharge chute, or near any moving part.
Keep hands, feet and clothing out of inlets and discharge openings while machine is operating to avoid serious personal injury. Check the cutting chamber to verify it is empty before starting the machine. Exclude pieces of metal, rocks, bottles, cans, and other foreign objects when feeding chipable material into the machine. Shut off engine immediately if the cutting mechanism strikes any foreign object or the machine starts making an unusual noise or vibrating.
Allow the machine to stop completely. After machine stops:. Replace or repair any damaged parts. Check for and tighten any loose parts. Do not allow processed material to build up in the discharge area; this may prevent proper discharge and can result in kickback of material through the feed opening. Stand clear of the discharge area when operating this machine. Keep your face and body back from the feed opening. Do not climb onto chipper shredder feed chutes or frame when operating.
Do not overreach. Keep proper balance and footing at all times. Keep the engine clear of debris and other accumulations. Do not tamper with the engine governor settings on the machine; the governor controls the maximum safe operating speed and protects the engine and all moving parts from damage caused by over speed.
Setting up your chipping site so you are not endangered by traffic and the public is not endangered by your work is critical for safety. Take great care to provide adequate warning by way of signage and coning, if diverting vehicles or pedestrian traffic is necessary. A well-prepared traffic plan includes parking off the highway whenever possible. Cone the work area as. Avoid sudden traffic stoppage or lane diversion. Do not allow pedestrians to walk through the work area.
Ensure chips or dust do not blow into traffic, parked cars, or pedestrians. Check the bolts on the following for correct torque every 10 hours of operation:. Chipper shredder rotor assembly bearings 80 ft lbs. Shredder Knives 36 In lbs. Failure to maintain proper fastening torque 20 ft. Shut off engine and allow machine to stop completely before clearing debris if the machine becomes clogged.
On electric start models, disconnect cables from battery before doing any inspection or service. Rotate the discharge tube to face the opposite direction of the towing vehicle before towing.
This prevents the discharge tube from projecting over the trailer wheels and striking foreign objects. Read and follow instructions on PTO safety decals. Stay alert and pay attention when PTO chipper is operating. Keep bystanders, especially children, away from PTO driveline.
Connect 3 pt. Check the driveline to ensure it is attached securely to the tractor. World's leading marketplace. This chipper is driven by a PTO and would make a great accessory to anyone with a tractor looking for and easy way to turn brush into wood chips it has a psi. Find best. Bear Cat chippers feature reversible chipper blades, cantilever rotor design and hydrostatic.
Bear Cat Chipper Parts Available. Woods OEM Parts. Skip to content Bearcat Wood Chipper 10 out of 10 based on ratings. For a Cold Engine — Gradually return the choke control to the off position after the engine starts and warms up.
The machine may be operated during the warm up period, but it may be necessary to leave the choke partially on until the engine warms up. For a Warm Engine — Return choke to the off position as soon as engine starts. Do not crank the engine continuously for more than 10 seconds at a time.
If the engine does not start, allow a. Failure to follow these guidelines can burn out, or permanently damage, the starter motor. If the engine develops sufficient speed to disengage the starter but does not keep running a false start , the engine rotation must be allowed to come to a complete stop before attempting to restart the engine. If the starter is engaged while the flywheel is rotating, damage to the starter may result.
If the starter does not turn the engine over, shut off starter immediately. Do not make further attempts to start the engine until the condition is corrected. Do not jump start using another battery. Follow the steps below to start the machine. Start the engine by activating the key switch. Release the switch as soon as the engine starts.
Move the throttle to the slow idle position. Disengage the engagement handle. Allow the engine to run at idle for seconds; stop the engine by moving the throttle to the low position or turn off ignition. Allow machine to come to a complete stop. The operator should always wear heavy boots, gloves, pants and a long-sleeved shirt. Use common sense and practice safety to protect yourself from branches, sharp objects, and other harmful objects.
The machine chips and shreds a variety of materials into a more readily decomposed or handled condition. The following guidelines will help you get started. Run unit at full operating speed before starting to chip material. Limbs fed in to the chipper chute must be 3 inches 7.
Trim side branches that cannot be bent enough to feed into the chipper chute. Common shredding materials include grass, leaves, garden refuse, sticks, and small branches.
Exclude pieces of metal, rocks, bottles, cans, and other foreign objects when feeding material into the machine. Feed brush from the side of the chipper chute, rather than from the front. Step aside to avoid being hit by the brush moving into the chipper. Place limb, butt end first, into the chipper chute until it contacts the chipper blades. The actual feed rate of the limb into the chipper will depend on the type of material fed and sharpness of the cutting blades.
If the engine slows to where it may stall, stop feeding material and allow the engine to recover. Feed material more evenly. If the chipper jams, remove the branch and rotate it before reinserting it into the chute.
Alternately insert and retract the limb or insert continuously at a rate that will not kill the engine. Never lean over the chipper chute to push objects into the cutting device. Use a push stick or brush paddle. Never use shovels or forks to feed brush. They can cause extensive damage if they contact the blades. In addition, metal pieces can be ejected from the chipper chute and cause serious injury or death.
Never use hands or feet to clear materials that build up in the chute. Do not use the clutch to clear a plugged rotor. This may cause belt damage. Refer to the instructions for clearing a plugged rotor in the Service and Maintenance section. Alternate greener material with dry material to lubricate the chipping blades for longer life and better performance.
Chipping dead, dry material will create heat and dull the chipping blades quickly. Sharpen the chipping blades periodically. Check the sharpness of the blades every hours. Refer to the Service and Maintenance section for sharpening instructions. To prevent personal injury or property damage: shut off engine and make sure that all moving parts have come to a complete stop before, servicing, adjusting or repairing. Disconnect the battery and remove ignition key where applicable.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Echo Bear Cat. They are 6-digit numbers. Box This warranty does not cover normal maintenance, service or adjustments.
The engine on your power equipment, like most outdoor power equipment, is an internal combustion engine that burns gasoline or diesel fuel hydrocarbons.
Therefore, your power equipment must be equipped with a spark arrester muffler in continuous effective working order. Keep hands and feet out of feed and discharge openings while machine is operating to avoid serious personal injury. Disconnectthebatteryandremove the ignition key if applicable. Tighten to proper torgue 3.
To prevent personal injury or property damage: Store fuel only in approved containers, in well ventilated, unoccupied buildings, away from sparks or flames. To add fuel: 1. Figure 2. Figure 3. WARNING Before operating your machine, be sure you read and understand all safety, controls and operating instructions in this owner's manual and on your machine.
If the engine does not start, allow a 60 second cool down period between starting attempts. Do not wear loose fitting clothing. Hold small diameter branches together in a bundle and feed in simultaneously.
Never feed brush into the chute with your feet. WARNING To prevent personal injury or property damage: shut off engine and make sure that all moving parts have come to a complete stop before, servicing, adjusting or repairing. You can only view or download manuals with. Sign Up and get 5 for free.
0コメント